Battery for Cub Cadet XT1 LT42: 725P17335
The Cub Cadet 725P17335 is a 12V AGM starting battery rated at 210 CCA with 11Ah capacity. Parts cross-references list it for selected XT1 LT42 tractors, yet LT42 variants use different batteries.
This page contains affiliate links. We may earn a commission if you buy through them, at no extra cost to you.
Will This Battery Fit Your XT1 LT42?
“XT1 LT42” is not enough to pick a battery. Cub Cadet lists some LT42 tractors with a 12V, 230 CCA lead-acid battery and others with a 12V, 210 CCA AGM battery. Run this quick check before you buy.
Cub Cadet lists the US XT1 LT42 IntelliPOWER model 13A6A9TS010 with a 12V, 230 CCA lead-acid battery, while its Canadian listing for model 13A6A9TS596 shows a 210 CCA AGM battery. The electric XT1 LT42E runs a 56V lithium-ion battery, which this 12V part does not replace.
Cub Cadet 725P17335 Specifications
| Property | Detail |
|---|---|
| Brand / part number | Cub Cadet 725P17335 |
| Cub Cadet description | 12-Volt AGM Lawn and Garden Battery – 210 CCA |
| Battery type | AGM (absorbent glass mat) lead-acid, rechargeable |
| Nominal voltage | 12 V |
| Cold-cranking amps | 210 CCA |
| Capacity | 11 Ah (per parts and retailer listings) |
| Design | Sealed AGM design; listings advertise non-spillable construction and higher vibration resistance |
| Earlier part numbers | 725-17335, 490-280-Y017, CMXGZAM280017 (per parts listings) |
| Replacement part (per Cub Cadet) | 490-280-F017, which lists 725P17335 as a part it replaces |
| Charging (Cub Cadet AGM manuals) | AGM charger at 1.1 A / 14.8 V; no automotive charger |
| Dimensions and weight | Not confirmed by Cub Cadet; retailer listings show differing figures |
| Warranty | Varies by product and purchase; check the documents supplied with your order |
Voltage, chemistry and CCA come from Cub Cadet’s product page. Capacity comes from parts and retailer listings. Exact case size, weight and terminal layout are left out because no reliable manufacturer figure was found.
XT1 LT42 Battery Replacement Difficulty
This is an easy job for most owners who are comfortable with basic hand tools. The work involves two cable connections and a hold-down, with no programming. Picking the right battery is the part most likely to go wrong. Tap a slice to highlight it.
- 20% Reaching the battery and hold-down
- 25% Disconnecting and reconnecting cables
- 35% Choosing the correct battery
- 20% Charging and safety checks
Corroded terminal hardware, missing screws or nuts, damaged cables, a wrong-size replacement, or a starting fault that was never the battery can all make the job harder.
The difficulty score and effort split are an editorial estimate based on the typical steps involved, not an official rating.
How to Replace Your Tractor Battery
Tap each step to tick it off as you go. Your operator’s manual is the final word on access and hardware for your model.
- 1Prepare the tractorPark on firm, level ground. Disengage the blades, apply the parking brake, switch off the engine, remove the key and let the engine cool. Disconnect the spark plug wires as an extra precaution.
- 2Disconnect the negative cableRemove the black negative cable first. Keep the fasteners together.
- 3Disconnect the positive cableSlide back the red boot and remove the positive cable second. Do not let a tool touch the frame while it contacts the positive terminal.
- 4Release the hold-down and lift out the batteryFree the hold-down rod or strap as fitted to your tractor. Note the battery’s orientation and cable routing, then lift the old battery out.
- 5Fit the new batteryPlace the charged replacement in the same orientation and secure the hold-down. Route the wiring as shown in your manual.
- 6Reconnect positive, then negativeAttach the red positive cable first and refit its boot. Connect the black negative cable last, and check that both are firm.
- 7Reconnect the spark plug wires and testRefit the spark plug wires, return the seat to its working position and start the tractor following your operator’s manual.
Fit a fully charged battery. Cub Cadet operator’s manuals for AGM-equipped tractors recommend an AGM charger at 1.1A and 14.8V, and say not to use an automotive charger.
Cub Cadet Models Cross-Referenced
Motobatt, an aftermarket battery maker, cross-references 725P17335 with these Cub Cadet models. Treat the list as a starting point, because fitment depends on the exact model and year. Cub Cadet’s own parts supplements also list 725P17335 as an AGM battery for some models.
- XT1 LT42Cross-referenced
- XT1 LT42BCross-referenced
- XT1 LT46Cross-referenced
- XT1 LT50 FabCross-referenced
- XT1 GT54 FabCross-referenced
- XT1 ST54 FabCross-referenced
- XT2 GX50 FabCross-referenced
- XT2 GX54D FabCross-referenced
- XT2 LX42 FabCross-referenced
- XT2 LX46 FabCross-referenced
- XT2 SLX50 FabCross-referenced
- XT2 SLX54 FabCross-referenced
- ZT1 zero-turns42, 42 Fab, 46, 50, 54 and 54P Fab
- ZT2 & ZT3 zero-turnsZT2-50/54/60 Fab, ZT3-60 Fab
- ZTS1 & ZTS2ZTS1-42/46/50, ZTS2-50/54/60 Fab
- ZTX4, ZTX5, ZTX648, 54 and 60 Fab sizes as listed
- ZTXS4, ZTXS5, ZTXS654 and 60 Fab sizes as listed
Safety, Charging & Disposal
Lead-acid batteries contain sulphuric acid and can give off explosive gas. Keep sparks and flames away, wear eye protection and protect your skin. Never open, dismantle, overheat or burn the battery.
- Disconnect negative first and reconnect it last.
- Use an AGM charger, never an automotive charger.
- Store the battery fully charged, with clean terminals.
- Disconnect the negative cable during long storage.
- Take the old battery to a battery retailer or household hazardous-waste collection point.
Cub Cadet 725P17335: FAQ
What battery does a Cub Cadet XT1 LT42 take?
It depends on the exact model. Cub Cadet lists some XT1 LT42 tractors with a 12V, 230 CCA lead-acid battery and others with a 12V, 210 CCA AGM battery. Use your tractor’s full model number to confirm the right replacement.
Does the 725P17335 fit every XT1 LT42?
No. Parts cross-references list it for selected XT1 LT42 applications, but no source confirms it for every year and configuration. Check your model number in Cub Cadet’s parts finder before ordering.
Is the 725P17335 a lithium battery?
No. It is a 12V AGM lead-acid starting battery. The electric XT1 LT42E uses a separate 56V lithium-ion battery, and the 725P17335 does not replace it.
How do 725P17335 and 490-280-F017 differ?
Cub Cadet lists 490-280-F017 as a replacement for 725P17335. Both are described as 12V, 210 CCA AGM batteries with 11Ah capacity.
Can I charge it with a car battery charger?
Cub Cadet operator’s manuals for AGM-equipped tractors say not to use an automotive charger. They recommend an AGM charger at 1.1A and 14.8V.
Does the battery need water or acid added?
No. It is a sealed AGM battery. Do not try to open it. Keep it charged, clean and stored properly instead.
My tractor still will not start after the replacement. Why?
A new battery does not cure every starting fault. Loose or corroded cables, a blown fuse, a safety switch, the solenoid or the starter can also stop the engine cranking. Cub Cadet also lists engaged blades and a disengaged parking brake among common causes of start failure.
How should I dispose of the old battery?
Do not put it in household rubbish or recycling bins. The US EPA notes that lead-acid batteries have an established collection network through retailers and other drop-off points.
